Each server has two or four on-board NIC's and two additional Mezzanine card-slots for additional I/O options: 1 Gb or 10 Gb Ethernet cards, Fibre Channel HBA's or InfiniBand slots. In an enclosure you can fit 8 full or 16 half-height blades (or a mix). In form-factor there are two models: half-height and full-height. The blade-servers in Generation 8 and Generation 9 are using another enclosure that is not compatible with the current M1000e system. Since Generation 10 there are models for the M1000e enclosure. The fourth digit indicates the make of the CPU, 0 for Intel and 5 for AMD.įor example: The Dell PowerEdge R6415 model is a rack, mid-range, 14th generation, single CPU socket system with AMD Processor.The third digit indicates the number of CPU sockets, 1 for one socket and 2 for two sockets.The second digit indicates the generation, with 0 for 10th generation, 1 for 11th generation and so on.The first digit after the letter indicates the class of the system, with 1– 5 defaulting to iDRAC Basic and 6– 9 defaulting to iDRAC Express.Whereas the R605 is a two-socket, 10th generation AMD-based rack-server. The third digit indicates the make of the CPU: 0 for Intel or 5 for AMD.įor example: The Dell PowerEdge M610 is a two-socket blade server of the 11th generation using an Intel CPU.The middle digit refers to the generation: 0 for Generation 10, 1 for Generation 11, and so on.The first digit refers to the number of sockets in the system: 1 to 3 for one socket, 4 to 7 for two sockets, and 8 or 9 for four sockets.This letter is then followed by three digits. The letter indicates the type of server: R (for Rack-mountable) indicates a 19″ rack-mountable server, M (for Modular) indicates a blade server, whilst T (for Tower) indicates a stand-alone server. Since the introduction of the Generation 10 servers in 2007 Dell has adopted a standardized method for naming their servers the name of each server is now represented by a letter followed by 3 digits. The Dell Itanium-based servers were introduced before this new naming-convention was introduced and were only available as rack servers. Over the years, many different types of PowerEdge servers have been introduced and there was wide variety of product and family codes used within the PowerEdge name. Most modern servers are either 1U or 2U high while in the past the 4U was more common. The 19″ rack-servers come in different physical heights expressed in rack units or U. In the current naming scheme, towers are designated by T, racks by R, and blades by M (for modular). Different models are or were available as towers, 19-inch racks or blades. The PowerEdge is a server line by Dell, following the naming convention for other Dell products: the PowerVault (data storage) and the PowerConnect (data transfer & switches).īelow is an overview of current and former servers within Dell's PowerEdge product line. You could also run diagnostics.Rack-mounted 11th-generation PowerEdge servers Your issues can be anything from a driver to an electrical problem. You should also review the system event logs of the blades further to look for additional errors. Are they scattered around the chassis or are they all next to each other in the chassis? Try moving them to different slots to see if the problem follows the blade or stays with the slot. Find out if they have anything in common that separates them from the other blades. If there are no power errors in the CMC then you should perform more information gathering and troubleshooting on the problem blades. Most of the errors you are receiving are typically symptoms of other problems.Ĭheck the CMC log to see if there are any reported power issues from the CMC. We just want to know what could possibly cause these kind of errors to the servers and what is the possible solutions, knowing the we tested the supposed to be defected CPUs in other servers and it works fine.
0 Comments
Leave a Reply. |